Mitsubishi GT10 series touch screen related issues
1, GT1030 Mitsubishi touch screen how to use USB for data transmission?
Use USB to 232 cable + QC30R2 connection, pay attention to the software to select the appropriate COM port
2, Mitsubishi touch screen suddenly lost power, after what will happen?
Instantaneous power-down <5ms, continue to action. Long time power outage, when the voltage is low, the touch screen action to stop; restore will automatically restart after power on.
3, Mitsubishi touch screen LCD with bright spots, black spots, but also flashing, is not the touch screen is not good?
Mitsubishi touch screen with bright spots (has been lit points) and black spots (not lit point) is the characteristics of the LCD screen. LCD screen has a lot of display components, it can not guarantee that 100% does not appear bright spots and black spots. In addition, depending on the display color, a blink may appear. There are bright spots, black spots or blinking, not the product is not good or fault, but its characteristics.
4, how to monitor communication among the Mitsubishi touch screen system menu?
You can enter the system menu by touching the upper and lower corners of the screen at the same time, then touch ‘Communication Settings’, then touch ‘Communication Monitoring’, where the white part on the black background indicates that no transmission or reception is performed.
5, Mitsubishi touch screen touch positioning is not accurate, how to calibrate?
Enter the touch screen system menu settings interface, select the ‘calibration’ menu, precise click on the [+] number until you return to the menu settings interface
Mitsubishi touch screen utility menu method of starting.
1. Without engineering data, after power-on, touch OK to display the utility menu.
2. When the screen is displayed, the default factory setting is to touch the upper left corner to display the utility menu. 3. Set the expansion function switch in the screen, select the utility menu to display the utility menu.
How to use the Mitsubishi touch screen window pops up automatically?
Assign a value to the window switching device, and specify the number of the specified popup window.
6, GT10 series Mitsubishi touch screen can simulate it?
The use of GT Simulator3 new software can be simulated, the software version needs more than 1.22Y support.
7, the alarm log display, can use different device alarm?
No, because in the common settings of GT10 series alarm log devices of Mitsubishi Touch Panel, only the continuous mode can be selected for the device settings, and the random mode can not be selected. Therefore, only continuous devices can be selected for the alarm log display function.
8, the key code switch ladder which shows why the press invalid?
GT10 series Mitsubishi touch screen ladder does not monitor the function.
9, when the bit device is ON or OFF, you can switch between different screens?
When the Mitsubishi touch screen bit device is ON or OFF, you can switch between different screens respectively. Screen switching is done by assigning values ​​to screen switching devices, and screen switching devices are word devices. You can set the condition bit device status in the condition monitoring function and assign a fixed value to the screen switching device during operation.
10, how to enter the text corresponding to the text and text?
Answer: The text to be displayed is registered in the comment or comment group. Then use the comment display (word) to display the function of the comment corresponding to the value of the word device.
11, how to install Mitsubishi touch screen GT10 basic OS, communication driver OS?
Answer: Press and hold the lower right corner, power on. The installation screen will appear, through the software to install the basic OS, communication driver OS
How to make the installation screen of install os on Mitsubishi touch screen GT1030-LBL-C?
Answer: Press the lower right corner of the power

Mitsubishi GT12 series touch screen related issues

1, Mitsubishi touch screen GT12 MODBUS can communicate with the PLC?
Answer: You can connect standard devices that support MODBUS / RTU protocol
2, record the year and month trends in the device how to set?
Answer: The value of “year” will be displayed in the device operation, the lower 4 bits of mask, AND FF00, and the right 8 bits. The value of “month” will be displayed in the device operation, and the mask is 4-digit high, AND 00FF.
3, Mitsubishi touch screen using multi-point connection can connect up to how long?
Answer: Including the multi-point serial connection module (GT01-CRS4-M) and the maximum distance between the PLC can be extended by 500 meters
4, Mitsubishi touch screen switch can enter the value?
Answer: The data write switch can be used to input the fixed value or indirect device value into the current device, but can not realize the pop-up value input keyboard input value.
5, Mitsubishi touch screen cable GT12 how to find the connection manual?
Answer: GT12 series is an upgraded version of the GT11 series, GT12 series of cables according to the GT11 series of search. GT12 series have Ethernet interface, Ethernet connection, according to GT15 series can be found.
6, Mitsubishi touch screen matrix impedance mode and analog impedance mode difference?
Answer: Mitsubishi touch screen panel has 2 kinds, analog (matrix impedance mode) and digital (analog impedance mode). Analog: You can press 2 points at the same time, the accuracy is poor. Positioning block digital quantity: Only 1 point can be pressed. If you press 2 points, the touch screen can not judge the specific point. It is mistakenly considered as a regional center.
7, Mitsubishi touch screen overlap window and overlay window What is the difference?
Answer: Overlap window is the pop-up window in the basic screen. You can move and close the window manually. The superimposed window is a composite window displayed in the basic screen. Overlay window and overlay window can only display 2 windows at the same time.
8, Mitsubishi touch screen GT12 can touch more at the same time?
Answer: No, the touch panel method of GT12 series is analog resistive film mode, and press the two points on the display at the same time. If there is a switch near the center of the press, it may cause the switch to operate.
9, Mitsubishi touch screen exit set the password screen, re-enter the screen how to still need to enter the password?
Answer: The screen will switch out of the security screen to switch to multi-action switch. Set two actions, respectively, set the word device for the security level of the device, the fixed value is set to 0, the security level is returned to 0; and the basic switch, fill in the required return screen number.
Mitsubishi GT15 / GT16 series touch screen related issues
1, ask Mitsubishi touch screen GT16 RS422 serial specialties?
Answer: is a special interface. Requires 422 interface of GT16-C02R4-9S (9-pin) or GT16-C02R4-25S (25-pin).
2, Mitsubishi touch screen GT16 series of multimedia features operating settings and support for multimedia file formats?
Answer: 1. Add GT16M-MMR CF card 2. Enter the main menu – video settings or extended function button inside the multimedia can enter the menu Supported formats: MP4 and 3GP
3, Mitsubishi touch screen clock settings in the time notification and time adjustment What is the difference?
Answer: The time notification is to use the touch screen to adjust the time of the connected PLC, so the battery to save its time. Time adjustment is by the PLC to adjust the touch screen time.
4, Mitsubishi GT15-75J61BT13-Z and GT15-J61BT13 What is the difference?
Answer: GT15-75J61BT13-Z is used in CCLINK Ver.1 mode, which consists of A8GT-61BT13 and GT15-76IF900, and GT15-J61BT13 is compatible with CCLINK Ver.2 mode. The former has stopped production.
5, the difference between file saving mode and buffer recording mode?
Answer: File saving mode: Used for storing a large amount of log data in the memory card. The saved log data can be saved on the PC after the Unicode clerical / CSV file is saved. Buffering Recording Mode: Multi-Purpose Edge Collecting High-Speed ​​Logs Appears in the GOT. Because the use of cache (RAM) will disappear after power failure.
6, GT15 / GT16 series of Mitsubishi touch screen area how to adjust?
Answer: In case of GT15: system menu screen -GOT setting-operation setting-touch screen to adjust setting, and then coordinate adjustment. In the case of GT16: System menu screen – Body function setting – Operation Adjust the setting on the touch panel and then adjust the coordinates.

Leave a Reply

Your email address will not be published. Required fields are marked *